1. Please use flash utility AWDFLASH v8.24F to update AI7 BIOS.
2. First release.
3. BIOS compile date: 09/23/2003

1. Change the default year after clear CMOS to 2003.
2. Add AMD Duron 1400(133)/1600(133)/1800(133) support.
3. Change the wording "DDR SDRAM at DIMM" to "DDR at DIMM" in order to match the wording on the PCB.
4. BIOS compile date: 08/29/2003.
   

1. Update HPT 374 BIOS from 1.1 to 1.22 to fix special boot sequence issue.
   • Use PS/2 keyboard and mouse simultaneously.
   • HDD attached to IDE 3 or 4.
   • CDROM attached to IDE2.
   • When above 3 description are true, booting up from Win 98SE floppy disk will fail to find some system files.
2. Fix system paused at C3 after cleared CMOS with Sumsung DDR K4H560838D Modul.
3. BIOS Compile Date: 10/11/2002.

1. Support Athlon XP 2400+, 2600+ CPU. Please be noted that Athlon XP 2400+ and 2600+ CPU need AMD certified heatsink; otherwise, the system will be quite unstable or even fail to boot up. Please check AMD recommended CPU cooler in following URL. http://www.amd.com/gb-uk/Processors/ComputingSolutions/0,,30_288_1274_3734^4348^4356,00.html
2. HPT 374 BIOS Version 1.21.
3. BIOS Compile Date: 8/22/2002

1. Support new 0.13micron process AthlonXP CPU-Throughbred.
2. HPT 374 BIOS Version 1.21.
3. BIOS Compile Date: 6/05/2002

1. Add the option "Onboard Lan Boot ROM". The default setting is "Disabled" that to shorten the booting time.
2. HPT 374 BIOS Version 1.21.
3. BIOS Compile Date: 04/09/2002.

1. First Release.
2. HPT 374 BIOS Version 1.21.
3. BIOS Compile Date: 04/03/2002.

1. HPT374 Driver version 1.23.  -**New**
2. For Win ME, Win2000, Win NT, Win XP.
   　

1. VIA Service Pack 4in1.
2. For WinMe, Win2000, Win XP.

1. HPT374 Driver.
2. For WinMe, Win2000, Win XP.

1. VIA USB Filter Driver.
2. For WinMe, Win2000, Win XP.

1. VIA USB 2.0 Driver.
2. For WinMe, Win2000, Win XP.

1. LAN Card Driver.
2. For WinMe, Win2000, Win XP.

1. Add AMD Duron 1400(133)/1600(133)/1800(133) support.
2. Fix the issue that the system occasionally hangs at post code 26 if the system is using 133/166 FSB CPU and the power was turned off during boot up procedure when the post code is AE.
3. HPT 374 BIOS version 1.23.
4. BIOS compile date: 08/28/2003.

1. Follow AMD's recommendation that" CPU Disconnect Function "should be implemented to make CPU slow down in idle state, and the default value sets up to Enable.
2. Follow AMD's recommendation to revise the trigger timing of LM90 for Palomino CPU(model 6).
3. Support Barton 2600+(333 FSB) and Thorton2000+(266 FSB)/2200+(266 FSB)/2400+(266 FSB)/2600+(333 FSB).
4. Revises some CPU frequency(1466,1666,1916,2166)to be AMD officially suggested figures.(1467,1667,1917,2167).
5. HPT 374 BIOS version 1.23.
6. BIOS compile date 3/27/2003.

BIOS ID: DC

1. The default year in BIOS up to 2003.
2. Fix Athlon XP 1400(100) CPU failure to power up by special operations:
   a. Discharge CMOS data.
   b. Enter BIOS Setup page.
   c. Save& Exit without doing anything.
3. Fix the reading of CPU Working Frequency for 166MHz CPU.
4. HPT374 BIOS version 1.22.
5. BIOS Compile Date: 01/08/2003.
   　

BIOS ID: C5

1. Provides CPU settings for AMD Athlon XP 2500+/2600+/2800+/3000+(333).

2. Fixes LAN transfer error after 96 hours continuous LAN test while CPU/DRAM = 100/133 and 100/166.

3. Revises the CPU and UUID information in DMI pool, and also fills in the SVID/SSID of IDE controller.

4. Fixes the issue that Windows 98SE shows corrupt screen with ATI Radeon 9700 Pro.

5. Adds "Enhance PCI Performance" function to improve PCI RAID performance.

6. Fixes "Shutdown When CPU overheat" and "Shutdown When CPU FAN Fail" function failure under Windows 2000.

7. Changes ACPI Code to pass HCT ACPI test.

8. HPT374 BIOS version 1.22.

9. BIOS Compile Date: 12/03/2002.

1. Support Athlon XP 2400+, 2600+ CPU. Please be noted that Athlon XP 2400+ and 2600+ CPU need AMD certified heatsink; otherwise, the system will be quite unstable or even fail to boot up. Please check AMD recommended CPU cooler in following URL.  http://www.amd.com/gb-uk/Processors/ComputingSolutions/0,,30_288_1274_3734^4348^4356,00.html
2. Provide CPU multiplier up to 22X in SoftMenu.
3. Enhance DDR333 stability while "Enhance DRAM Performance" enabled.
4. Fix LAN transfer error in 72 hours continuous LAN test while CPU/DRAM = 100/133 and 100/166.
5. Support AMD new coming 333 CPU.
6. In case over clock the CPU frequency higher than 180MHz, don't press reset button otherwise the system will refuse to boot up. It's a auto protect mechanism to prevent possible hardware damage caused by abnormal working environment.
7. HPT 374 BIOS Version 1.21.
8. BIOS compile date: 9/9/2002.

1. First release.
2. HPT 374 BIOS Version 1.21.
3. BIOS compile date: 8/12/2002.

1. HPT374 Driver version 1.23.  -**New**
2. For Win ME, Win2000, Win NT, Win XP.
   　

1. Support Athlon XP 2400+, 2600+ CPU. Please be noted that Athlon XP 2400+ and 2600+ CPU need AMD certified heatsink; otherwise, the system will be quite unstable or even fail to boot up. Please check AMD recommended CPU cooler in following URL.  http://www.amd.com/gb-uk/Processors/ComputingSolutions/0,,30_288_1274_3734^4348^4356,00.html
2. Provide CPU multiplier up to 22X in SoftMenu.
3. Enhance DDR333 stability while "Enhance DRAM Performance" enabled.
4. Fix LAN transfer error in 72 hours continuous LAN test while CPU/DRAM = 100/133 and 100/166.
5. Support AMD new coming 333 CPU.
6. In case over clock the CPU frequency higher than 180MHz, don't press reset button otherwise the system will refuse to boot up. It's a auto protect mechanism to prevent possible hardware damage caused by abnormal working environment.
7. HPT 374 BIOS Version 1.21.
8. BIOS compile date: 9/9/2002.

1. First release.
2. HPT 374 BIOS Version 1.21.
3. BIOS compile date: 8/12/2002.

1. Update awdflash.exe (Award BIOS Flash Utility) version to v8.22A.

1. AWDFLASH v8.24F is for ABIT KV7, KD7A, VI7, IS-50, VA-10, VA-11, IS-10 and IS-12 only.
2. For other ABIT motherboards launched before July 2003, use AWDFLASH v8.23K to update BIOS.
3. File size: 40982 Bytes
4. MD5(AWDFLASH.EXE)= d99df64b353f9a286a62601011e41caa
5. Release date: 8/11/2003

1. For ABIT motherboards launched before July 2003, use AWDFLASH v8.23K to update BIOS.
2. For ABIT KV7, KD7A, VI7, IS-50, VA-10, VA-11, IS-10, IS-12, and other motherboards launch after July 2003, use AWDFLASH v8.24F please.
3. File size: 40,420 Bytes
4. MD5(AWDFLASH.EXE)= 599f89f864254cc338e6ddb5320f143d

1. First release.
2. BIOS compile date: 4/24/2002

1. Fixes issue where the Load Fail-Safe/Optimized Default, the setting of Drive A/Drive B/Floppy 3 Mode/Video/Halt On in Standard CMOS Features, would not return to defaults.
2. Fixes issue where the "Shutdown When CPU FAN Fail" option fails after about 16 minutes idling under Windows 2000/XP.
3. Fixes the incompatibility issue where the ATI Radeon 9700Pro fails to boot up with a certain power supply unit- TC-350P. With this power supply, 9700Pro will fail to boot, and the reset button needs to be pressed once to show the bootup screen.
4. HPT 372 BIOS Version 2.32. The RAID function is for BD7-RAID only. This BIOS version is also for non RAID boards and HPT BIOS will be automatically disabled when the RAID controller chip is not detected.
5. BIOS Compile Date: 11/12/2002

1. Willamette CPU will be automatically detected its FSB while Load Fail-Safe/Optimized Default in Bios Setup of SoftMenu.
   Fill in new CPU micro code (0F27).
2. Provide multiplier higher than 24x in SoftMenu.
3. Fix some CL=3 DDR400 memory modules fail to boot issue. (Both DDR333 and DDR400 modules can only work at DDR 266 owing to 845 chipset specification.)
4. Fix "CPU Shutdown Temperature" function failed under Win2K.
5. HPT 372 BIOS Version 2.32. The RAID function is for BD7-RAID only. This BIOS version is also for non RAID boards and HPT BIOS will be automatically disabled while RAID controller chip not detected.
6. BIOS compile Date: 9/11/2002.

1. Modify the DMI data to fix on line diagnostic tool issue (PC Pitstop).
2. HPT 37x BIOS version 2.31. The RAID function is for BD7-RAID only. This BIOS version is also for non RAID boards and HPT BIOS will be automatically disabled while RAID controller chip not detected.
3. BIOS compile date: 7/02/2002

1. Raise the adjustable CPU Core Voltage for 0.13 micron process P4 (Northwood).
2. Support Pentium 4 2.4G CPU.
3. Fix occasional no POST with debug code 26 issue while "Fixed PCI=33" option was enabled in Softmenu III.
4. Support P4 Celeron CPU.
5. HPT 37x BIOS version 2.31. The RAID function is for BD7-RAID only. This BIOS version is also for non RAID boards and HPT BIOS will be automatically disabled while RAID controller chip not detected.
6. BIOS compile date: 5/02/2002

!!! Attention for upgrading BIOS!!! * When you upgrade bios to new bios included HPT 2.31 bios, we highly recommend you backup your system and data to an independent storage device first. New HPT 2.31 bios may corrupt original RAID configuration created on old bios occasionally. That means you may need to rebuild RAID configuration. If it happens, all the data on RAID-0 will be gone! * For RAID-1 user, please press "CTRL+H" to enter hpt37x setup.*Please upgrade HPT 2.31 driver before upgrade bios.

BIOS ID: 6H

1. Add" High Performance" option in " Load Optimized Defaults". "High Performance" option will use critical DDR memory timing settings to achieve high system performance, nevertheless, it may deviate the original settings from module SPD and cause system instability.
   
2. HPT 37x BIOS version 2.0.1024.The RAID function is for BD7-RAID only. This BIOS version is also for non RAID boards and HPT BIOS will be automatically disabled while RAID controller chip not detected.

BIOS ID: 4X

1. First release.
   
2. HPT 37x BIOS version 2.0.1024. The RAID function is for BD7-RAID only. This BIOS version is also for non RAID boards and HPT BIOS will be automatically disabled while RAID controller chip not detected.

1. Fixes the issue while S4 resumed, the MAC Address of onboard LAN chip can not correctly display.
2. Adds the following settings for "CPU Shutdown Temperature".
   1. 80C/176F
   2. 85C/185F
   3. 90C/194F
3. Changes the default setting of "CPU Warning Temperature".
4. Fixes the problem that if 'Land Boot Rom' setup to Enable, it would hang while resumed from S4 mode.
5. Revises the item help of "Shut down When CPU Fan Fail".
6. BIOS Compile Date: 6/17/2003.

1. First release.
2. BIOS Compile Date: 4/22/2003.
   　

1. Fixes issue where the Load Fail-Safe/Optimized Default, the setting of Drive A/Drive B/Floppy 3 Mode/Video/Halt On in Standard CMOS Features, would not return to defaults.
2. Fixes issue where the "Shutdown When CPU FAN Fail" option fails after about 16 minutes idling under Windows 2000/XP.
3. Fixes the incompatibility issue where the ATI Radeon 9700Pro fails to boot up with a certain power supply unit- TC-350P. With this power supply, 9700Pro will fail to boot, and the reset button needs to be pressed once to show the bootup screen.
4. HPT 372 BIOS Version 2.32. The RAID function is for BD7-RAID only. This BIOS version is also for non RAID boards and HPT BIOS will be automatically disabled when the RAID controller chip is not detected.
5. BIOS Compile Date: 11/12/2002

1. Willamette CPU will be automatically detected its FSB while Load Fail-Safe/Optimized Default in Bios Setup of SoftMenu.
   Fill in new CPU micro code (0F27).
2. Provide multiplier higher than 24x in SoftMenu.
3. Fix some CL=3 DDR400 memory modules fail to boot issue. (Both DDR333 and DDR400 modules can only work at DDR 266 owing to 845 chipset specification.)
4. Fix "CPU Shutdown Temperature" function failed under Win2K.
5. HPT 372 BIOS Version 2.32. The RAID function is for BD7-RAID only. This BIOS version is also for non RAID boards and HPT BIOS will be automatically disabled while RAID controller chip not detected.
6. BIOS compile Date: 9/11/2002.

1. Modify the DMI data to fix on line diagnostic tool issue (PC Pitstop).
2. HPT 37x BIOS version 2.31. The RAID function is for BD7-RAID only. This BIOS version is also for non RAID boards and HPT BIOS will be automatically disabled while RAID controller chip not detected.
3. BIOS compile date: 7/02/2002

1. Raise the adjustable CPU Core Voltage for 0.13 micron process P4 (Northwood).
2. Support Pentium 4 2.4G CPU.
3. Fix occasional no POST with debug code 26 issue while "Fixed PCI=33" option was enabled in Softmenu III.
4. Support P4 Celeron CPU.
5. HPT 37x BIOS version 2.31. The RAID function is for BD7-RAID only. This BIOS version is also for non RAID boards and HPT BIOS will be automatically disabled while RAID controller chip not detected.
6. BIOS compile date: 5/02/2002

!!! Attention for upgrading BIOS!!! * When you upgrade bios to new bios included HPT 2.31 bios, we highly recommend you backup your system and data to an independent storage device first. New HPT 2.31 bios may corrupt original RAID configuration created on old bios occasionally. That means you may need to rebuild RAID configuration. If it happens, all the data on RAID-0 will be gone! * For RAID-1 user, please press "CTRL+H" to enter hpt37x setup.*Please upgrade HPT 2.31 driver before upgrade bios.

BIOS ID: 6H

1. Add" High Performance" option in " Load Optimized Defaults". "High Performance" option will use critical DDR memory timing settings to achieve high system performance, nevertheless, it may deviate the original settings from module SPD and cause system instability.
   
2. HPT 37x BIOS version 2.0.1024.The RAID function is for BD7-RAID only. This BIOS version is also for non RAID boards and HPT BIOS will be automatically disabled while RAID controller chip not detected.

BIOS ID: 4X

1. First release.
   
2. HPT 37x BIOS version 2.0.1024. The RAID function is for BD7-RAID only. This BIOS version is also for non RAID boards and HPT BIOS will be automatically disabled while RAID controller chip not detected.

1. Fills MAC Address into UUID section in DMI data to pass WHQL.
2. Changes the definition of UUID in DMI data- move the MAC address from top to bottom of the string.
3. Fixes issue where the Shutdown When "CPU FAN Fail" option fails after about 16 minutes idling under Windows 2000/XP.
4. Fixes the compatibility issue where the ATI Radeon 9700 Pro fails to boot up with a certain power supply unit - TC-350P. With this power supply, the 9700 Pro will fail to boot up, requiring a reset button push to show the boot screen.
6. Shows "Hyper-Threading" wording on POST screen when Hyper-Threading CPU installed
7. HPT 372 BIOS Version 2.32. The RAID function is for BD7II-RAID only. This BIOS version is also for non RAID boards and HPT BIOS will be automatically disabled when the RAID controller chip is not detected.
8. BIOS Compile Date: 11/28/2002.

1. Fill in new CPU micro code (0F27).
2. HPT 372 BIOS Version 2.32. The RAID function is for BD7II-RAID only. This BIOS version is also for non RAID boards and HPT BIOS will be automatically disabled while RAID controller chip not detected.
3. BIOS compile Date: 9/17/2002.

1. Upgrade the BIOS code for ICH4 to V1.5.
2. Fill in new CPU micro code (0F27).
3. Support PMC Pm49FL004T 4Mb Flash ROM.
4. Provide multiplier higher than 24x in SoftMenu.
5. Fix some CL=3 DDR400 memory modules fail to boot issue.(Both DDR333 and DDR400 modules can only work at DDR 266 owing to 845E chipset specification.)
6. Fix "CPU Shutdown Temperature" function failed under Win2K.
7. HPT 372 BIOS Version 2.32. The RAID function is for BD7II-RAID only. This BIOS version is also for non RAID boards and HPT BIOS will be automatically disabled while RAID controller chip not detected.
8. BIOS compile Date: 8/26/2002.

1. Fix multimedia device lost issue with 533MHz FSB CPUs while load Fail-Safe / Optimized Default in BIOS.
2. Add SVID and SSID for ICH4 USB 2.0 controller.(SVID:147B,SSID:7402)
3. Load proper setting automatically for Willamette CPU when Load Fail-safe/Optimized Default in BIOS.
4. HPT 37x BIOS version 2.31. The RAID function is for BD7II-RAID only. This BIOS version is also for non RAID boards and HPT BIOS will be automatically disabled while RAID controller chip not detected.
5. BIOS compile date: 7/23/2002.

1. Northwood CPU will be automatically detected its FSB while Load Fail-Safe/Optimized Default in BIOS Setup of SoftMenu.
2. Differentiate the USB 1.1 from USB 2.0 controller on PCI Device listing screen.
3. Fix Boot Agent failed to boot-up while enabled the Boot ROM in BIOS with hard disk on High-Point Port.
4. Modify the DMI data to fix on line diagnostic tool issue (PC Pitstop).
5. HPT 374 BIOS Version 1.21.
6. BIOS compile date: 7/02/2002

1. Add an option "Enhance DRAM Performance" in Advanced Chipset Features.

2. HPT 37x BIOS Version 2.31 The RAID function is for BD7II-RAID only. This BIOS version is also for non RAID boards and HPT BIOS will be automatically disabled while RAID controller chip not detected

3. BIOS compile date: 5/3/2002.

!!!Attention for upgrading BIOS!!!
*When you upgrade bios to new bios included HPT 2.31 bios, we highly recommend you backup your system and data to an independent storage device first. New HPT 2.31 bios may corrupt original RAID configuration created on old bios occasionally. That means you may need to rebuild RAID configuration. If it happens, all the data on RAID-0 will be gone!
* For RAID-1 user, please press "CTRL+H" to enter hpt37x setup.
* Please upgrade HPT 2.31 driver before upgrade bios.

1. First release.
2. HPT 372 BIOS version 2.0.1024. The RAID function is for BD7II-RAID only. This BIOS version is also for non RAID boards and HPT BIOS will be automatically disabled while RAID controller chip not detected.
3. BIOS compile date: 4/19/2002

1. Fills MAC Address into UUID section in DMI data to pass WHQL.
2. Changes the definition of UUID in DMI data- move the MAC address from top to bottom of the string.
3. Fixes issue where the Shutdown When "CPU FAN Fail" option fails after about 16 minutes idling under Windows 2000/XP.
4. Fixes the compatibility issue where the ATI Radeon 9700 Pro fails to boot up with a certain power supply unit - TC-350P. With this power supply, the 9700 Pro will fail to boot up, requiring a reset button push to show the boot screen.
6. Shows "Hyper-Threading" wording on POST screen when Hyper-Threading CPU installed
7. HPT 372 BIOS Version 2.32. The RAID function is for BD7II-RAID only. This BIOS version is also for non RAID boards and HPT BIOS will be automatically disabled when the RAID controller chip is not detected.
8. BIOS Compile Date: 11/28/2002.

1. Fill in new CPU micro code (0F27).
2. HPT 372 BIOS Version 2.32. The RAID function is for BD7II-RAID only. This BIOS version is also for non RAID boards and HPT BIOS will be automatically disabled while RAID controller chip not detected.
3. BIOS compile Date: 9/17/2002.

1. Upgrade the BIOS code for ICH4 to V1.5.
2. Fill in new CPU micro code (0F27).
3. Support PMC Pm49FL004T 4Mb Flash ROM.
4. Provide multiplier higher than 24x in SoftMenu.
5. Fix some CL=3 DDR400 memory modules fail to boot issue.(Both DDR333 and DDR400 modules can only work at DDR 266 owing to 845E chipset specification.)
6. Fix "CPU Shutdown Temperature" function failed under Win2K.
7. HPT 372 BIOS Version 2.32. The RAID function is for BD7II-RAID only. This BIOS version is also for non RAID boards and HPT BIOS will be automatically disabled while RAID controller chip not detected.
8. BIOS compile Date: 8/26/2002.

1. Fix multimedia device lost issue with 533MHz FSB CPUs while load Fail-Safe / Optimized Default in BIOS.
2. Add SVID and SSID for ICH4 USB 2.0 controller.(SVID:147B,SSID:7402)
3. Load proper setting automatically for Willamette CPU when Load Fail-safe/Optimized Default in BIOS.
4. HPT 37x BIOS version 2.31. The RAID function is for BD7II-RAID only. This BIOS version is also for non RAID boards and HPT BIOS will be automatically disabled while RAID controller chip not detected.
5. BIOS compile date: 7/23/2002.

1. Northwood CPU will be automatically detected its FSB while Load Fail-Safe/Optimized Default in BIOS Setup of SoftMenu.
2. Differentiate the USB 1.1 from USB 2.0 controller on PCI Device listing screen.
3. Fix Boot Agent failed to boot-up while enabled the Boot ROM in BIOS with hard disk on High-Point Port.
4. Modify the DMI data to fix on line diagnostic tool issue (PC Pitstop).
5. HPT 374 BIOS Version 1.21.
6. BIOS compile date: 7/02/2002

1. Add an option "Enhance DRAM Performance" in Advanced Chipset Features.

2. HPT 37x BIOS Version 2.31 The RAID function is for BD7II-RAID only. This BIOS version is also for non RAID boards and HPT BIOS will be automatically disabled while RAID controller chip not detected

3. BIOS compile date: 5/3/2002.

!!!Attention for upgrading BIOS!!!
*When you upgrade bios to new bios included HPT 2.31 bios, we highly recommend you backup your system and data to an independent storage device first. New HPT 2.31 bios may corrupt original RAID configuration created on old bios occasionally. That means you may need to rebuild RAID configuration. If it happens, all the data on RAID-0 will be gone!
* For RAID-1 user, please press "CTRL+H" to enter hpt37x setup.
* Please upgrade HPT 2.31 driver before upgrade bios.

1. First release.
2. HPT 372 BIOS version 2.0.1024. The RAID function is for BD7II-RAID only. This BIOS version is also for non RAID boards and HPT BIOS will be automatically disabled while RAID controller chip not detected.
3. BIOS compile date: 4/19/2002

1. Fix "CPU THRM-Throttling" function.
2. Fill in new CPU micro code (0F27).
3. Support Intel P4 Celeron 2.0G CPU.
4. Fix some CL=3 DDR400 memory modules fail to boot issue.(Both DDR333 and DDR400 modules can only work at DDR 266 owing to 845 chipset specification.)
5. Fix "CPU Shutdown Temperature" function failed under Win2K.
6. BIOS compile Date: 9/11/2002.

1. First Release.
2. Support Intel Pentium4 2.2AGHz CPU.

1. Adds support for Celeron II CPU 633 MHz and up to 700MHz .
2. Fixes the keyboard LED still on issue after shutting down the system under Windows operating system.

1. Supports PIII 750Mhz, 800Mhz,850Mhz(100Mhz FSB) CPUs and Celeron 667Mhz,700(66)Mhz CPUs.

1. Supports the Celeron 533A(66),566(66) and 600(66)Mhz CPUs.
   
2. Improves the power on funtion by mouse right/left botton after shoutting down the system under Win98SE.
   
3. Fixes the incorrect memory capacity issue under Linux.
   
4. Fixes the ACPI issue under Windows2000.
   
5. Improves the IRO assignment funtion.
   

1. Supports PIII 600Mhz(100Mhz FSB), 650(100Mhz FSB) and 700Mhz(100Mhz FSB) CPUs.
   
2. Updates HPT 366 BIOS to Rev. 1.21.

1. Supports the Celeron 533Mhz(66Mhz FSB) CPU.
   
2. Updates the BIOS or the HPT 366 controller to version 1.2.
   
3. Fixes the boot failure issue with SCO UNIX.
   
4. Fixes the system hang up issue when the ESCD record is incorrect.
   

1. Supports the PIII 600(100)Mhz CPU.
   
2. Supports Socket 370 Celeron 500 Mhz CPU.
   
3. Fixes the Y2K RTC problem.
   
4. Fixes the password function.
   
5. Improves the STD function.
   
6. Supports the A, EXT, C option.
   
7. Supports 40GB harddisks and above, However we aren't quite sure what the precise capacity is, since the current maximun harddisk on the market is 40GB.
   

1. First release.

1. Support Intel PIII / Celeron CPUs up to1.1G(100). (Please mention: This board does not support Tualatin core PIII / Celeron processors.)
   
2. HPT 366 BIOS version: 1.25.
   

BIOS ID: XU

1. Supports Celeron 800(100)MHz CPUs.
2. Supports FlashMenu.
3. HPT 366 BIOS version 1.25.

BIOS ID: VN

1. Add PCI/Latency timer function in PnP/PCI Configurations
   
2. Support Flash Menu.
   
3. HPT 366 BIOS verson 125.

BIOS ID: UH

1. Supports to PIII 1GHz CPU(133MHz FSB).
   

BIOS ID: SH

1. Supports Celeron 566(66),600(66),667(66),700(66)and PIII850(100),866(133) and 933(133) MHz CPUs.
   

BIOS ID: RV

1. Improves the 133 Mhz option in SoftMenu.
   
2. Fixes the hard disk detection failure issue when putting the CD ROM drive on IDE 1, and sets the boot sequence as CDROM first.
   
3. Fixes the incorrect memory capacity issue under Linux.
   
4. Fixes the HighPoint display problem with AHA-2940A and TNT AGP cards.
   
5. Fixes the Wake on Ring, Wake on Lan, and Wake on Alarm problems under Win98SE
   
6. Increases the CPU Warning Temperture funtion to solve Win98SE ShoutDown Problems when OEM CPU temperture is detected as too high.
   
   

BIOS ID: QJ

1. For users who try to overclock the FSB up to 133 Mhz, but fail when using some AGP video cards which can't run at that frequency in 2X mode.
   
2. Supports PIII CPUs up to 800MHz.
   
3. Increases SDRAM compatibility.
   
   

1. Supports I2C debug card.
   
2. Adds an AGP transfer mode for choosing AGP transfer mode.

1. Supports PIII 600Mhz(100Mhz FSB), 650Mhz(100Mhz FSB) and 700Mhz(100Mhz FSB) CPUs.
   
2. Updates HPT 366's BIOS to rev. 1.21.
   
3. Shows the correct frequency as set by User Define.

1. Solves the boot failure issue when switching the CPU to another one.
   
2. Solves the auto detection function while putting a CDROM on IDE 1 master.

1. First release.

BIOS ID: 71

1. Support Intel PIII/Celeron up to 1.1G(100) CPU.(Please mention: This board does not support Tualatin core P!!!/Celeron processors.)
   
2. HPT 370 BIOS version:0.95b.
   

BIOS ID: ZX

1. Support Intel Coppermine CPU.
   
2. Support Flashmenu utility.
   
3. HPT 370 BIOS version 095b.

BIOS ID: XV

1. Support Celeron 800 MHz(100) CPU.
   
2. Support Flash Menu.
   
3. HPT 370 BIOS verson 095b.
   
   

BIOS ID: VP

1. Support Celeron 633,733,766 MHz(66) CPU.
   
2. Add Idle/Pipeline DRAM Leadoff function in Advanced Chipset Feature
   
3. Add PCI/Latency timer function in PnP/PCI Configurations
   
4. Support Flash Menu.
   
5. HPT 370 BIOS verson 095b.
   
   
   

BIOS ID: UJ

1. Supports Celeron CPU up to 633MHz(66MHz FSB), and PIII CPUs up to 1GHz (133MHz FSB).
   
   

BIOS ID: SV

1. Supports PIII 850(100),866(133)MHz CPUs.
   
2. Fixes boot up failure issue on Coppermine PIII 800(133), Celeron 566(66)MHz CPU and above.
   
3. Changes I/O Voltage Default to +3.5V.
   
   

BIOS ID: RW

1. Supports Celeron 566(66),600(66),667(66) and 700(66)MHz CPUs.
   
2. Fixes the IrDA Function Failed issue under Win98SE
   This BIOS is for the BE6-II version 1.2 with the HPT 370 controller chip only!
   
   
   

BIOS ID: RP

1. First release.
   This BIOS is for the BE6-II version 1.2 with the HPT 370 controller chip only!

BIOS ID: 72

1. Support Intel PIII/Celeron up to 1.1G(100) CPU.(Please mention: This board does not support Tualatin core P!!!/Celeron processors.)
   
2. HPT 370 RAID BIOS verson 1.0.3b1.

BIOS ID: XK

1. Support Celeron 800MHz(100) CPU.
   
2. Supports FlashMenu.
   
3. HPT 370 RAID BIOS verson 1.0.3b1.

BIOS ID: VI

1. Support Celeron 633MHz(66) CPU.
   
2. Add Idle/Pipeline DRAM Leadoff option in BIOS.
   
3. Add PCI latency timer function in BIOS .
   
4. Fix displayed error in issue.
   
5. Support Flash Menu.
   
6. HPT 370 RAID BIOS verson 1.0.3b1.

BIOS ID: UK

1. First release.

1. Systems can not detects the fan speed and automatically shut down while using low rotation speed fan.
2. Adjust the SP_LED as following to conform to the requirement:
   S0.........Always on
   S1........ Blink (faster frequency)
   S3.........Blink (slower frequency)If the LED could not support different blinking frequency, it would behave like S1 state.
   S4.........Always off
   S5.........Always off
3. Fix the multiplier of unlocked CPU shows incorrectly while resumed
   from STR.
4. Update CPU micro code.（0F24/18, 0F27/33, 0F29/0E）
5. HPT372 BIOS version 2.32
6. BIOS compile date 3/27/2003.

1. Fixes the compatibility issue where the ATI Radeon 9700 Pro fails to boot up with a certain power supply unit - TC-350P. With this power supply, the 9700 Pro will fail to boot up, requiring a reset button push to show the boot screen.
2. Changes the definition of UUID in DMI data- move the MAC address from top to bottom of the string.
3. Shows "Hyper-Threading" wording on POST screen when Hyper-Threading CPU installed.
4. HPT 372 BIOS Version 2.32.The RAID function is only for BE7-RAID. The BIOS is suitable for non-RAID boards and it will automatically disable HPT BIOS when non-RAID boards are recognized.
5. BIOS Compile Date: 11/28/2002.

1. MAC Address fills into UUID section in DMI data in order to pass WHQL.
2. Shows MAC Address of on board LAN Card in System Configuration section.
3. Shows "Award BIOS" on BIOS Setup Utility.(Used be "Work station BIOS")
4. Fixes Windows flash utility invalidity when using Hyper-Threading CPU.
5. Fixes issue where if the "Shutdown When CPU FAN Fail" option fails after about 16 minutes idling under Windows 2000/XP.
6. HPT 372 BIOS Version 2.32.The RAID function is only for the BE7-RAID. The BIOS is suitable for non-RAID boards and it will automatically disable the HPT BIOS when non-RAID boards are recognized.

1. First release.
2. HPT 372 BIOS Version 2.32. The RAID function is for BE7-RAID only. This BIOS version is also for non RAID boards and HPT BIOS will be automatically disabled while RAID controller chip not detected.
3. BIOS compile Date: 9/05/2002.

1. Systems can not detects the fan speed and automatically shut down while using low rotation speed fan.
2. Adjust the SP_LED as following to conform to the requirement:
   S0.........Always on
   S1.........Blink (faster frequency)
   S3.........Blink (slower frequency)If the LED could not support different blinking frequency, it would
                behave like S1 state.
   S4.........Always off
   S5.........Always off
3. Fix the multiplier of unlocked CPU shows incorrectly while resumed
   from STR.
4. Update CPU micro code.（0F24/18, 0F27/33, 0F29/0E）
5. BIOS Compile Date: 4/25/2003.
   　

BIOS ID: 10

1. First Release.
2. BIOS Compile Date: 12/17/2002.
   　

1. Systems can not detects the fan speed and automatically shut down while using low rotation speed fan.
2. Adjust the SP_LED as following to conform to the requirement:
   S0.........Always on
   S1.........Blink (faster frequency)
   S3.........Blink (slower frequency)If the LED could not support different blinking frequency, it would
                behave like S1 state.
   S4.........Always off
   S5.........Always off
3. Fix the multiplier of unlocked CPU shows incorrectly while resumed
   from STR.
4. Update CPU micro code.（0F24/18, 0F27/33, 0F29/0E）
5. BIOS Compile Date: 4/25/2003.
   　

BIOS ID: 10

1. First Release.
2. BIOS Compile Date: 12/17/2002.
   

1. Systems can not detects the fan speed and automatically shut down while using low rotation speed fan.
2. Adjust the SP_LED as following to conform to the requirement:
   S0.........Always on
   S1........ Blink (faster frequency)
   S3.........Blink (slower frequency)If the LED could not support different blinking frequency, it would behave like S1 state.
   S4.........Always off
   S5.........Always off
3. Fix the multiplier of unlocked CPU shows incorrectly while resumed
   from STR.
4. Update CPU micro code.（0F24/18, 0F27/33, 0F29/0E）
5. HPT372 BIOS version 2.32
6. BIOS compile date 3/27/2003.

1. Fixes the compatibility issue where the ATI Radeon 9700 Pro fails to boot up with a certain power supply unit - TC-350P. With this power supply, the 9700 Pro will fail to boot up, requiring a reset button push to show the boot screen.
2. Changes the definition of UUID in DMI data- move the MAC address from top to bottom of the string.
3. Shows "Hyper-Threading" wording on POST screen when Hyper-Threading CPU installed.
4. HPT 372 BIOS Version 2.32.The RAID function is only for BE7-RAID. The BIOS is suitable for non-RAID boards and it will automatically disable HPT BIOS when non-RAID boards are recognized.
5. BIOS Compile Date: 11/28/2002.

1. MAC Address fills into UUID section in DMI data in order to pass WHQL.
2. Shows MAC Address of on board LAN Card in System Configuration section.
3. Shows "Award BIOS" on BIOS Setup Utility.(Used be "Work station BIOS")
4. Fixes Windows flash utility invalidity when using Hyper-Threading CPU.
5. Fixes issue where if the "Shutdown When CPU FAN Fail" option fails after about 16 minutes idling under Windows 2000/XP.
6. HPT 372 BIOS Version 2.32.The RAID function is only for the BE7-RAID. The BIOS is suitable for non-RAID boards and it will automatically disable the HPT BIOS when non-RAID boards are recognized.

1. First release.
2. HPT 372 BIOS Version 2.32. The RAID function is for BE7-RAID only. This BIOS version is also for non RAID boards and HPT BIOS will be automatically disabled while RAID controller chip not detected.
3. BIOS compile Date: 9/05/2002.

1. Systems can not detects the fan speed and automatically shut down while using low rotation speed fan.
2. Adjust the SP_LED as following to conform to the requirement:
   S0.........Always on
   S1.........Blink (faster frequency)
   S3.........Blink (slower frequency)If the LED could not support different blinking frequency, it would
                behave like S1 state.
   S4.........Always off
   S5.........Always off
3. Fix the multiplier of unlocked CPU shows incorrectly while resumed
   from STR.
4. Update CPU micro code.（0F24/18, 0F27/33, 0F29/0E）
5. BIOS Compile Date: 4/25/2003.
   　

BIOS ID: 10

1. First Release.
2. BIOS Compile Date: 12/17/2002.
   

SATA driver disk V1.2

1. Support Intel PIII / Celeron CPUs up to1.1G(100). (Please mention: This board does not support Tualatin core PIII / Celeron processors.)
   
2. HPT 366 BIOS version: 1.25.
   

BIOS ID: XU

1. Support Celeron 800MHz(100) CPU.
   
2. Support Flash Menu.

BIOS ID: UH

1. Supports to PIII 1GHz CPU(133MHz FSB).

BIOS ID: SH

1. Supports Celeron 566(66),600(66),667(66),700(66)and PIII850(100),866(133) and 933(133) MHz CPUs.

BIOS ID: RV

1. Improves the 133 Mhz option in SoftMenu.
   
2. Fixes the hard disk detection failure issue when putting the CD ROM drive on IDE 1, and sets the boot sequence as CDROM first.
   
3. Fixes the incorrect memory capacity issue under Linux.
   
4. Fixes the HighPoint display problem with AHA-2940A and TNT AGP cards.
   
5. Fixes the Wake on Ring, Wake on Lan, and Wake on Alarm problems under Win98SE .
   
6. Improve the CPU Warning Temperture funtion to solve Win98SE shout down problem that OEM CPU temperture was detected too high.

BIOS ID: QJ

1. For users who try to overclock the FSB up to 133 Mhz, but fail when using some AGP video cards which can't run at that frequency in 2X mode.
   
2. Supports PIII CPUs up to 800MHz.
   
3. Increases SDRAM compatibility.

1. Supports I2C debug card.
   
2. Adds an AGP transfer mode for choosing AGP transfer mode.

1. Supports PIII 600Mhz(100Mhz FSB), 650Mhz(100Mhz FSB) and 700Mhz(100Mhz FSB) CPUs.
   
2. Updates HPT 366's BIOS to rev. 1.21.
   
3. Shows the correct frequency as set by User Define.

1. Solves the boot failure issue when switching the CPU to another one.
   
2. Solves the auto detection function while putting a CDROM on IDE 1 master.
   

1. First release.

BIOS ID: BC

1. Fixes the issue that Intel Celeron 2G can not show the correct CPU ID/uCode ID and Cache size.
2. Modify to support up to 3.0 multiplier frequency.
3. The CPU type of Northwood and Celeron will be automatically recognized while loading optimized and fail-safe default.
4. The multiplier frequency opens for adjusting while use "user define" option.
5. BIOS Compile Date: 12/18/2002
   　

1. Fix PS/2 mouse can't work after waken from S4 mode while USB keyboard/mouse installed together.
2. BIOS compile date: 7/19/2002.

1. First release.
2. BIOS compile date: 7/12/2002

BIOS ID: D5

1. The APIC Mode option Enabled and highlighted in BIOS while used Hyper-Threading CPU.(It would turn out to be normally while Hyper-Threading Technology set up to Disabled.)
2. "CPU Hyper-Threading" option in "Advanced BIOS Features' revised to "Hyper-Threading Technology" to fit in with the requirement of Intel.
3. Show "Hyper-Threading" wording on POST screen when Hyper-Threading CPU installed.
4. Show MAC Address of on board LAN Card in System Configuration section.
5. Change the definition of UUID in DMI data- move the MAC address from top to bottom of the string.
6. Revise DMI Pool data.
7. BIOS Compile Date: 12/16/2002

BIOS ID: D4

1. Show MAC Address of on board LAN Card in System Configuration section.
2. Change the definition of UUID in DMI data- move the MAC address from top to bottom of the string.
3. Revise DMI Pool data.
4. BIOS Compile Date: 12/16/2002

1. Fixes the incompatibility issue where the ATI Radeon 9700Pro fails to boot up with a certain power supply unit- TC-350P. With this power supply, 9700Pro will fail to boot, and the reset button needs to be pressed once to show the bootup screen.

2. Fixes issue where the "Shutdown When CPU FAN Fail" option fails after about 16 minutes idling under Windows 2000/XP.

3. Adds functions to SoftMenu III.
   A.   Auto detects CPU speed. It offers User Define and CPU frequency in CPU Operation Speed option.
   B.   CPU frequency locks up for Northwood CPU. It would not
          allow users to choose multiplier factor but shows CPU
          multiplier factor on it.
   C.   CPU Operation Speed in SoftMenu III reveals CPU frequency
          when user load defaults.

4. Fixes issue where ES North Wood 2.8G CPU detection fails.

5. BIOS compile Date: 11/14/2002.

1. Support Celeron 2.0G CPU.
2. Provide multiplier higher than 25x in SoftMenu.
3. Fill in new CPU micro code (0F27).
4. "Speed Error Hold"  function set to invisible.
5. Add "Disable Unused PCI Clock" function in Advanced BIOS Features that manages the Clock function on PCI slot.
6. Fix S3 Compliance failed while testing HCT 10.0 under Win XP.
7. BIOS compile date: 9/23/2002.

1. Support PMC PM49FL004T Flash ROM.
2. Support Winbond W39V040FA Flash ROM.
3. Modify boot issue of Mushkin DDR 400 module.
4. BIOS compile Date: 8/23/2002.

1. Support P4 2.8GHz (533MHz FSB) CPU. (CPU ID 0F27 Micro Code)
2. Add SVID and SSID for ICH4 USB 2.0 controller.(SVID:147B,SSID:7403)
3. BIOS compile date: 8/09/2002

1. Update VGA BIOS to 2656.
2. Enhance the DDR SDRAM setting table in "Advanced Chipset Feature".
3. Add "Enhance DRAM Performance" function.
4. Modify the DMI data to fix on line diagnostic tool issue (PCI Pitstop).
5. Set "Video RAM Cacheable", "AGP Data Transfer Rate", "AGP Aperture Size", "AGP Data Rate" and "AGP Enable" function to invisible while using OnBoard VGA card.
6. Hide "On-Chip Frame Buffer Size" option while using AGP Card.
7. BIOS compile date: 6/26/2002.
8. Please use AWDFLASH Ver. 8.20A to flash BIOS 94. We have include the program in BG794.EXE, but if you get the bg7_94.bin only and you are using AWDFLASH Ver. 7.97D, apply below special switches please. "AWDFLASH KG7_94.BIN /PY /SN /CD /CP /CC /F"

1. First release.
2. BIOS compile date: 5/03/2002

1. Fix the problem that MultiMedia device disappeared while using 533 FSB CPU after into BIOS to load default and save BIOS.
2. BIOS Compile Date: 4/25/2003.

BIOS ID: D6

1. Raise the upper limit of CPU core voltage to 1.85V.
2. Fix the booting failure issue when the system starts up from "CMOS checksum error" and without CPU fan attached to FAN2 header.
3. HPT 374 BIOS Version 1.22.
4. BIOS Compile Date: 12/16/2002.

BIOS ID:  CA

1. Fixes the incompatibility issue where ATI Radeon 9700Pro fails to boot up with a certain power supply unit -TC-350P. With this power supply, 9700Pro will fails to boot and the reset button needs to be pushed in order to show the bootup screen.

2. Fixes issue where the "Shutdown When CPU FAN Fail" option fails after about 16 minutes idling under Windows 2000/XP.

3. Adds functions in SoftMenu III.
   A.   Auto detects CPU speed. It offers User Define and CPU frequency in CPU
          Operation Speed option.
   B.   CPU frequency locks up for Northwood CPU. It would not allow users to choose
          multiplier factor but shows the CPU multiplier factor.
   C.   CPU Operation Speed in SoftMenu III reveals CPU frequency while user load defaults.

4. Fixes issue where ES Northwood 2.8G CPU is not detected automatically.

5. SP-LED blanks when system enters suspend mode.

6. BIOS Compile Date: 11/25/2002.

1. First Release.
2. BIOS Compile Date: 10/02/200.

1. First release.
2. BIOS compile date: 4/24/2002

1. Changed the default setting of "Power on by Ring" to disabled.
2. BIOS Compile date: 7/14/2003.

1. First release.
2. BIOS Compile Date: 7/14/2003.

Note:
*1: SA6R V1.0 and 1.1 can be easily distinguished by checking for a VGA Out port. Version 1.0 features this port, whereas version 1.1 does not.
GG

BIOS ID: SS

1. Supports Celeron 633(66),667(66),700(66)MHz CPUs.
   

BIOS ID: QN

1. Fixes the incorrect memory capacity issue under Linux.
   
2. Fixes the ACPI issue under Windows 2000
   
3. Supports Celeron 533a(66),566(66)and 600(66) MHz CPUs.
   

BIOS ID: NV

1. Supports the PIII 600Mhz(100Mhz FSB) CPU.
   
2. Supports 40GB harddisks and above, However we aren't quite sure what the precise capacity is, since the current maximun harddisk on the market is 40GB.
   

BIOS ID: LN

1. Fixes the Y2K RTC problem.
   
2. Supports Socket 370 Celeron 500 Mhz CPU.
   
3. Improves the IRQ assignment function.
   
4. Improves the TURBO FREQUENCE function in CPU SoftMenu section.
   
5. Fixes the password function.

BIOS ID: LH

1. Supports the socket 370 Celeron 466 Mhz CPU.
   
2. Supports the PIII 550Mhz CPU.

BIOS ID: KJ

1. Revises the BIOS to pass the Year 2000 RTC Rollover test.
   
2. Supports the Socket 370 Celeron 466 Mhz CPU.
   
3. This BIOS can not pass the critical CMOS reading and writing test in PCCHECK.EXE. It will be ready in the next BIOS.

BIOS ID: KG

1. Supports the PIII CPU Processor Serial Number function, it's called Processor Number Feature in the BIOS Features Setup section.
   
2. Supports assigned manual PCI IRQ in the PCI Onbard section.

BIOS ID: JJ

1. Supports Socket 370 Celeron 433 MHz CPU
   
2. Supports correct naming of Pentium III CPU.

BIOS ID: HN

1. Fixes NEC ATAPI ZIP drive incompatibility problem.
   
2. Supports Intel Pentium III 450 and 500 Mhz Katmai CPU.
   
3. Supports Intel Celeron 366 Mhz CPU option, up to 400 Mhz compliance.
   
4. Supports the clock multiplier up to 8 times.
   
5. Solves the problem of Windows98 not being able to shut-down properly when the ACPI function is enabled.
   
6. Supports DMI 2.3 . You have to input /CD parameter to Clear DMI pool data while updating the BIOS.
   

EXTRA NOTE:

For Pentium III (Katmai) users, the BIOS will indicate PII EVEN if it is a PIII because the code was finished just prior to the unveiling of the new PIII name for the Katmai. This will be corrected in the next BIOS.

BIOS ID: GY

1. Updates the K/B default setting to 8Mhz to fix Microsoft Elite K/Bs.
   
2. Changes the ACPI default setting to disable.

BIOS ID: FU

1. Supports ACPI function.
   
2. When upgrading to the BH6 FU BIOS, please use AWDFLASH.EXE 6.6 to avoid upgrade failure.

BIOS ID: FL

1. Supports the Celeron 300 and 333 CPUs with built-in cache.
   
2. The BH6 uses 2M EEPRAM, please use the AWDFLASH.EXE 6.22 version (or newer) for upgrades.
   
   

SDSFSDF

BIOS ID: SP

1. Supports the Celeron566(66),600(66),667(66),700(66)MHz CPUs, and PIII 750(100),800(100)MHz,850(100)MHz CPUs.
   
   

BIOS ID: QM

1. Shows memory larger than 64MB accurately in Linux.
   
2. Solves the problem of Windows 2000 not being able to shut down properly when the ACPI function is enabled.
   
3. Allows for accurate recognition of I740 VGA cards.
   
   

BIOS ID: PM

1. Supports the PIII 600Mhz(100Mhz FSB), 650Mhz(100Mhz) and 700Mhz(100Mhz) CPUs.
   
   

BIOS ID: NX

1. Supports the Celeron 533Mhz(66Mhz FSB) CPU.
   
2. Supports 40GB harddisks and above, However we aren't quite sure what the precise capacity is, since the current maximun harddisk on the market is 40GB.
   
3. Fixes the system hang up issue when the ESCD record is incorrect.
   

BIOS ID: NK

1. Supports the PIII 600(100) Mhz CPU.
   
2. Supports Socket 370 Celeron 500 Mhz CPU.
   
3. Fixes the Y2K RTC problem.
   
4. Fixes the password function.
   
5. Improves the manual IRQ assignment function.
   
6. Supports the Processor Number Feature option.
   
7. Fixes the CAS Latency Time function.
   

BIOS ID: LG

1. Supports Intel PIII 550Mhz CPU.

BIOS ID: KK

1. First release.
   
2. For Rev. 1.1 boards ONLY.
   Please check your boards version number on the ISA slot.

1. Revise CPU Temperature in "PC Health" again.
2. Fixes the problem if set up 'Land Boot Rom' Enable, it would hang while resumed from S4 mode.
3. Adds the item help of "Smart Fan Speed Control".
4. The Hardware Monitoring tool needs to be updated to"HWM_BH7V15.EXE" together with BIOS update.
5. BIOS Compile Date: 6/17/2003.

1. BH7 ve BH7-E için destek eklendi.
2. S4 Resume edildiğinde yerleşik LAN çipinin MAC adresinin düzgün görünmemesi sorunu giderildi.
3. "CPU Shutdown Temperature" seçeneklerine aşağıdaki değerler eklendi:
   1. 80C/176F
   2. 85C/185F
   3. 90C/194F
4. "CPU Warning Temperature" seçeneğinin varsayılan değeri değiştirildi.
5. BIOS Derleme Tarihi: 5/28/2003.

BIOS ID:12

1. Fixes S3 resume fail issue.
2. BIOS compile date: 3/14/2003.
   

BIOS ID:11

1. Fix intermittent VGA initialization failure when CPU FSB/DRAM Clock =100/133.
2. Revises the behavior of "Smart Fan Speed Control" function.
3. Fixes misreading OVT issue during POST process.
4. BIOS Compilation Date: 2/21/2003.

BIOS ID:10

1. First release.
2. BIOS Compilation Date: 2/19/2003.

1. Intel Application Accelerator.
2. Driver for Win 98se, Win Me, Win 2000, Win XP.

1. LAN driver (RTL 8100B / 8101B 10/100 Mb)
2. Driver for Win 98se, Win Me, Win 2000, Win XP.

1. Audio driver.
2. Driver for Win 98se, Win Me, Win 2000, Win XP.

1. USB 2.0 for ICH4.
2. Driver for Win 98se,Win Me.

1. Hardware Monitor
2. Need BIOS 1.5 or later

1. Revise CPU Temperature in "PC Health" again.
2. Fixes the problem if set up 'Land Boot Rom' Enable, it would hang while resumed from S4 mode.
3. Adds the item help of "Smart Fan Speed Control".
4. The Hardware Monitoring tool needs to be updated to"HWM_BH7V15.EXE" together with BIOS update.
5. BIOS Compile Date: 6/17/2003.

1. First release.
2. BIOS Compile Date: 5/28/2003.

1. Hardware Monitor
2. Need BIOS 1.5 or later

1. Fix ACPI error in system event viewer after resume Windows XP from STR mode.
2. Support P4 Celeron CPU.
3. BIOS compile date: 5/31/2002.

1. Load proper setting automatically for Willamette CPU when Load Fail -safe/Optimized Default in BIOS.
2. Support Celeron 2.0G CPU (for BL7/BL7-RAID only).
3. Support PMC Pm49FL004T 4Mb Flash ROM.
4. Fill in new CPU micro code (0F27).
5. HPT 37x BIOS version 2.0.1024. The RAID function is for BL7-RAID and BW7-RAID only. This BIOS version is also for non RAID boards and HPT BIOS will be automatically disabled while RAID controller chip not detected.
6. BIOS compile date: 9/16/2002.

1. Modify the DMI data to fix on line diagnostic tool issue (PC Pitstop).
2. HPT 37x BIOS version 2.0.1024. The reason to change BIOS v2.31 to v2.0.1024 are as below:

• System can not resume from STR mode under Win XP, while HDD connected onto HighPoint IDE Port by using HPT v2.31 BIOS.
• Improve performance declined on HPT BIOS v2.31 issue.

3. BIOS compile date: 7/02/2002.

1. Support Pentium 4 2.4G CPU.
2. Fix occasional no POST with debug code 26 issue while "Fixed PCI=33" option was enabled in Softmenu III.
3. Support P4 Celeron CPU.
4. HPT 37x BIOS version 2.31. The RAID function is for BD7-RAID and BW7-RAID only. This BIOS version is also for non RAID boards and HPT BIOS will be automatically disabled while RAID controller chip not detected.
5. BIOS compile date: 5/14/2002.

!!!Attention for upgrading BIOS!!!
* When you upgrade bios to new bios included HPT 2.31 bios, we highly recommend you backup your system and data to an independent storage device first. New HPT 2.31 bios may corrupt original RAID configuration created on old bios occasionally. That means you may need to rebuild RAID configuration. If it happens, all the data on RAID-0 will be gone!
* For RAID-1 user, please press "CTRL+H" to enter hpt37x setup.
*Please upgrade HPT 2.31 driver before upgrade bios.

1. The Default of year setup to 2002.
2. Raise the adjustable CPU Core Voltage for Pentium 4 processor.
3. Fix ACPI error in system event viewer after resume from STR mode.
4. HPT BIOS Version 2.0.1024.
5. BIOS Compile Date: 3/14/2002.

BIOS ID: 5K

1. Fix the CD-ROM boot issue on the SCSI cards.
2. Fix the unbootable issue when installing a hard disk onto IDE-2 and set the boot sequence by following as HDD_1, HDD_0 then floppy.
3. HPT BIOS version: 2.0.1024.

BIOS ID: 5C

1. Fix the option "Shutdown When CPU Fan Fail" set to Enable, cause system delayed issue.
2. Improve the STR function.
3. HPT 370 RAID BIOS version: 1.11.0402.

BIOS ID: 3H

1. First release.
2. HPT370 BIOS version: 1.11.0402.

1. Load proper setting automatically for Willamette CPU when Load Fail -safe/Optimized Default in BIOS.
2. Support Celeron 2.0G CPU (for BL7/BL7-RAID only).
3. Support PMC Pm49FL004T 4Mb Flash ROM.
4. Fill in new CPU micro code (0F27).
5. HPT 37x BIOS version 2.0.1024. The RAID function is for BL7-RAID and BW7-RAID only. This BIOS version is also for non RAID boards and HPT BIOS will be automatically disabled while RAID controller chip not detected.
6. BIOS compile date: 9/16/2002.

1. Modify the DMI data to fix on line diagnostic tool issue (PC Pitstop).
2. HPT 37x BIOS version 2.0.1024. The reason to change BIOS v2.31 to v2.0.1024 are as below:

• System can not resume from STR mode under Win XP, while HDD connected onto HighPoint IDE Port by using HPT v2.31 BIOS.
• Improve performance declined on HPT BIOS v2.31 issue.

3. BIOS compile date: 7/02/2002.

1. Support Pentium 4 2.4G CPU.
2. Fix occasional no POST with debug code 26 issue while "Fixed PCI=33" option was enabled in Softmenu III.
3. Support P4 Celeron CPU.
4. HPT 37x BIOS version 2.31. The RAID function is for BD7-RAID and BW7-RAID only. This BIOS version is also for non RAID boards and HPT BIOS will be automatically disabled while RAID controller chip not detected.
5. BIOS compile date: 5/14/2002.

!!!Attention for upgrading BIOS!!!
* When you upgrade bios to new bios included HPT 2.31 bios, we highly recommend you backup your system and data to an independent storage device first. New HPT 2.31 bios may corrupt original RAID configuration created on old bios occasionally. That means you may need to rebuild RAID configuration. If it happens, all the data on RAID-0 will be gone!
* For RAID-1 user, please press "CTRL+H" to enter hpt37x setup.
*Please upgrade HPT 2.31 driver before upgrade bios.

1. The Default of year setup to 2002.
2. Raise the adjustable CPU Core Voltage for Pentium 4 processor.
3. Fix ACPI error in system event viewer after resume from STR mode.
4. HPT BIOS Version 2.0.1024.
5. BIOS Compile Date: 3/14/2002.

BIOS ID: 5K

1. Fix the CD-ROM boot issue on the SCSI cards.
2. Fix the unbootable issue when installing a hard disk onto IDE-2 and set the boot sequence by following as HDD_1, HDD_0 then floppy.
3. HPT BIOS version: 2.0.1024.

BIOS ID: 5C

1. Fix the option "Shutdown When CPU Fan Fail" set to Enable, cause system delayed issue.
2. Improve the STR function.
3. HPT 370 RAID BIOS version: 1.11.0402.

BIOS ID: 3H

1. First release.
2. HPT370 BIOS version: 1.11.0402.

BIOS ID: TZ

1. Fixes the keyboard LED still on issue after shutting down the system under Windows operating system.

BIOS ID: QT

1. Fixes the incorrect memory capacity issue under Linux.
   
2. Fixes the ACPI issue under W2K.
   
3. Improves the Power On function by mouse right/left botton after shutting down the system under Win98SE.
   
4. Supports 1.5V (cB0 stepping) Celeron 566(66) and 600(66) MHz CPUs. CC0 and newer stepping Celeron CPUs are not supported.

BIOS ID: PQ

1. Supports Celeron 533Mhz(66Mhz FSB) CPUs.
   
2. Supports 40GB harddisks and above.

BIOS ID: MQ

1. Fixes the password function.
   
2. Supports Socket 370 Celeron 500 Mhz CPU.

BIOS ID: KV

1. Supports Socket 370 Celeron 466 Mhz CPU.
   
2. Fixes the Y2K RTC function.
   
3. Improves the IRQ assignment function.

BIOS ID: JN

1. Supports Socket 370 Celeron CPU up to 433 Mhz.

BIOS ID: HL

1. First release.

BIOS ID: RU

1. Fixes the CPU usage always showing 80% in Win 2000 problem.

BIOS ID: NJ

1. Supports Celeron 533Mhz(66Mhz FSB) CPUs.
   
2. Fixes the STD function.
   
3. HPT 366 BIOS version 1.21.
   
4. Adds the 'A, EXT, C' option.
   
5. Fixes the general password issue.
   
6. Supports 40GB harddisks and above.
   
7. Supports MPS rev 1.4.
   
8. Supports Power recovery function after the AC power back. (You may enable it under INTERGRATED PERIPHERALS of CMOS SETUP.)

1. First release.
   
2. Supports Socket 370 Celeron 500 Mhz CPU.

1. Load proper setting automatically for Willamette CPU when Load Fail -safe/Optimized Default in BIOS.
2. Support Celeron 2.0G CPU (for BL7/BL7-RAID only).
3. Support PMC Pm49FL004T 4Mb Flash ROM.
4. Fill in new CPU micro code (0F27).
5. HPT 37x BIOS version 2.0.1024. The RAID function is for BL7-RAID and BW7-RAID only. This BIOS version is also for non RAID boards and HPT BIOS will be automatically disabled while RAID controller chip not detected.
6. BIOS compile date: 9/16/2002.

1. Modify the DMI data to fix on line diagnostic tool issue (PC Pitstop).
2. HPT 37x BIOS version 2.0.1024. The reason to change BIOS v2.31 to v2.0.1024 are as below:

• System can not resume from STR mode under Win XP, while HDD connected onto HighPoint IDE Port by using HPT v2.31 BIOS.
• Improve performance declined on HPT BIOS v2.31 issue.

3. BIOS compile date: 7/02/2002.

1. Support Pentium 4 2.4G CPU.
2. Fix occasional no POST with debug code 26 issue while "Fixed PCI=33" option was enabled in Softmenu III.
3. Support P4 Celeron CPU.
4. HPT 37x BIOS version 2.31. The RAID function is for BD7-RAID and BW7-RAID only. This BIOS version is also for non RAID boards and HPT BIOS will be automatically disabled while RAID controller chip not detected.
5. BIOS compile date: 5/14/2002.

!!!Attention for upgrading BIOS!!!
* When you upgrade bios to new bios included HPT 2.31 bios, we highly recommend you backup your system and data to an independent storage device first. New HPT 2.31 bios may corrupt original RAID configuration created on old bios occasionally. That means you may need to rebuild RAID configuration. If it happens, all the data on RAID-0 will be gone!
* For RAID-1 user, please press "CTRL+H" to enter hpt37x setup.
*Please upgrade HPT 2.31 driver before upgrade bios.

1. The Default of year setup to 2002.
2. Raise the adjustable CPU Core Voltage for Pentium 4 processor.
3. Fix ACPI error in system event viewer after resume from STR mode.
4. HPT BIOS Version 2.0.1024.
5. BIOS Compile Date: 3/14/2002.

BIOSID: 5K

1. Fix the CD-ROM boot issue on the SCSI cards.
2. Fix the unbootable issue when installing a hard disk onto IDE-2 and set the boot sequence by following as HDD_1, HDD_0 then floppy.
3. HPT BIOS version: 2.0.1024.

BIOSID: 5B

1. Fix some P4-423 1.5G and 1.7G CPU compatibility issue with BW7 mainboard.
2. HPT BIOS Revision: 1.11.0402.

BIOSID: 5C

1. Fix the option "Shutdown When CPU Fan Fail" set to Enable, cause system delayed issue.
2. Improve the STR function.
3. HPT 370 RAID BIOS version: 1.11.0402.

BIOSID: 3H

1. First release.
2. HPT370 BIOS version: 1.11.0402.

1. Load proper setting automatically for Willamette CPU when Load Fail -safe/Optimized Default in BIOS.
2. Support Celeron 2.0G CPU (for BL7/BL7-RAID only).
3. Support PMC Pm49FL004T 4Mb Flash ROM.
4. Fill in new CPU micro code (0F27).
5. HPT 37x BIOS version 2.0.1024. The RAID function is for BL7-RAID and BW7-RAID only. This BIOS version is also for non RAID boards and HPT BIOS will be automatically disabled while RAID controller chip not detected.
6. BIOS compile date: 9/16/2002.

1. Modify the DMI data to fix on line diagnostic tool issue (PC Pitstop).
2. HPT 37x BIOS version 2.0.1024. The reason to change BIOS v2.31 to v2.0.1024 are as below:

• System can not resume from STR mode under Win XP, while HDD connected onto HighPoint IDE Port by using HPT v2.31 BIOS.
• Improve performance declined on HPT BIOS v2.31 issue.

3. BIOS compile date: 7/02/2002.

1. Support Pentium 4 2.4G CPU.
2. Fix occasional no POST with debug code 26 issue while "Fixed PCI=33" option was enabled in Softmenu III.
3. Support P4 Celeron CPU.
4. HPT 37x BIOS version 2.31. The RAID function is for BD7-RAID and BW7-RAID only. This BIOS version is also for non RAID boards and HPT BIOS will be automatically disabled while RAID controller chip not detected.
5. BIOS compile date: 5/14/2002.

!!!Attention for upgrading BIOS!!!
* When you upgrade bios to new bios included HPT 2.31 bios, we highly recommend you backup your system and data to an independent storage device first. New HPT 2.31 bios may corrupt original RAID configuration created on old bios occasionally. That means you may need to rebuild RAID configuration. If it happens, all the data on RAID-0 will be gone!
* For RAID-1 user, please press "CTRL+H" to enter hpt37x setup.
*Please upgrade HPT 2.31 driver before upgrade bios.

1. The Default of year setup to 2002.
2. Raise the adjustable CPU Core Voltage for Pentium 4 processor.
3. Fix ACPI error in system event viewer after resume from STR mode.
4. HPT BIOS Version 2.0.1024.
5. BIOS Compile Date: 3/14/2002.

BIOSID: 5K

1. Fix the CD-ROM boot issue on the SCSI cards.
2. Fix the unbootable issue when installing a hard disk onto IDE-2 and set the boot sequence by following as HDD_1, HDD_0 then floppy.
3. HPT BIOS version: 2.0.1024.

BIOSID: 5B

1. Fix some P4-423 1.5G and 1.7G CPU compatibility issue with BW7 mainboard.
2. HPT BIOS Revision: 1.11.0402.

BIOSID: 5C

1. Fix the option "Shutdown When CPU Fan Fail" set to Enable, cause system delayed issue.
2. Improve the STR function.
3. HPT 370 RAID BIOS version: 1.11.0402.

BIOSID: 3H

1. First release.
2. HPT370 BIOS version: 1.11.0402.

BIOS ID: 72

1. Support Intel PIII / Celeron CPUs up to 1.1G(100). (Please mention: This board does not support Tualatin core P!!!/Celeron processors.)
   
2. HPT 370 RAID BIOS verson 2.0.1024.

BIOS ID: ZW

1. Support Intel Coppermine CPU.
   
2. Support FlashMenu utility.
   
3. HPT 370 RAID BIOS version 1.0.3b1.

BIOS ID: XK

1. Support Celeron 800MHz(100) CPU.
   
2. Supports FlashMenu.
   
3. HPT 370 RAID BIOS verson 1.0.3b1.

BIOS ID: VI

1. Support Celeron 633MHz(66) CPU.
   
2. Add Idle/Pipeline DRAM Leadoff option in BIOS .
   
3. Add PCI latency timer function in BIOS .
   
4. Fix displayed error in issue.
   
5. Support Flash Menu.
   
6. HPT 370 RAID BIOS verson 1.0.3b1.

BIOS ID: UK

1. Supports to PIII 1GHz CPU(133MHz FSB).

BIOS ID: TT

1. Supports VIA Cyrix III CPU.
   

BIOS ID: SZ

1. First release.
   

BIOS ID: QS

1. Fixes the incorrect capacity issue under Linux.
   
2. Fixes the incompatibility issue with W2K.

BIOS ID: MX

1. Supports Celeron 533Mhz(66Mhz FSB) CPUs.
   
2. Supports PIII 600Mhz(100Mhz FSB) CPUs.
   
3. Supports 40GB harddisks and abov.

BIOS ID: MP

1. Fixes the password function.
   
2. Supports Socket 370 Celeron 500 Mhz CPU.

BIOS ID: LW

1. Fixes the password function.
   
2. Supports Socket 370 Celeron 500 Mhz CPU.

BIOS ID: JL

1. Supports Socket 370 Celeron 433 Mhz CPU.
   
2. Supports correct naming of Pentium III CPU.

BIOS ID: HV

1. Fixes the NEC ATAPI ZIP drive incompatibility problem.
   
2. Supports the Intel Pentium III 450 and 500 Mhz (Katmai) CPU.
   
3. Supports the Intel Celeron 366 Mhz up to 400 Mhz compliance.
   
4. Supports up to an 8x clock multiplier.
   
5. Solves the problem of Windows98 not being able to shut-down properly when the ACPI function is enabled.
   
6. Supports DMI 2.3 . You have to input the parameter /CD to Clear DMI pool data while updating the BIOS. (e.g. A:AWDFLASH NEWBIOS /PY /SN /CC /CD)
   

EXTRA NOTE:

For Pentium III (Katmai) users, the BIOS will indicate PII EVEN if it is a PIII because the code was finished just prior to the unveiling of the new PIII name for the Katmai. This will be corrected in the next BIOS.

BIOS ID: GX

1. Updates the K/B default setting to 8Mhz to fix Micorsoft Elite K/Bs.
   
2. Changes the ACPI default setting to disable.
   

BIOS ID: GQ

1. Supports ACPI function.
   

BIOS ID: EG

1. Supports some kinds of display cards with the chipset of Mpact 2.
2. Allows insertion of more than one display card on the mainboard & add s an Init Display First option in the BIOS for user to choose the primary display card.
3. Supports the Celeron 300 & 333 CPUs with built-in cache.

BIOS ID: DL

1. Correction for Intel Celeron parameters.
   
2. Correction for DRAM parameters and expanded support for more types of DRAM.

BIOS ID: CW

1. Supports Soft Menu II.
   
2. Supports SDRAM CAS Lattency Time in BIOS.

BIOS ID: AM

1. First release.
   

BIOS ID: QR

1. Fixes the incorrect memory capacity issue under Linux.
   
2. Fixes the ACPI issue under W2K.
   
3. Improves the Power On function by mouse right/left botton after shutting down the system under Win98SE.
   
4. Supports Celeron 566(66) and 600(66) MHz CPUs.

BIOS ID: NW

1. Supports PIII 600Mhz(100Mhz FSB), 650Mhz(100Mhz FSB) and 700Mhz(100Mhz FSB) CPUs.
   
2. Supports 40GB harddisks and above.
   
3. Supports Socket 370 Celeron 533Mhz(66Mhz FSB) CPUs.

BIOS ID: MW

1. Supports the PIII 600(100)Mhz CPU.
   
2. Supports Socket 370 Celeron 500 Mhz CPU.

BIOS ID: MN

1. Fixes the password function.

BIOS ID: LU

1. Fixes the Y2K RTC function.
   
2. Improves the IRQ assignment function.
   
3. Improves the CPU SOFTMENU fuction when turbo mode is enabled.

BIOS ID: KU

1. Supports Socket 370 Celeron 466 Mhz CPU.
   
2. Supports the PIII 550Mhz CPU.

BIOS ID: KH

1. Supports the PIII CPU Processor Serial Number function, it's called Processor Number Feature in the BIOS Features Setup.

BIOS ID: JH

1. Supports Socket 370 Celeron 433 Mhz CPU.
   
2. Supports correct naming of Pentium III CPU.

BIOS ID: HJ

1. First release.

1. First release.
2. BIOS Compile date: 7/29/2003.

ABIT-Engineered Flash Menu is a Windows-based BIOS flashing application.
FlashMenu™ will update your BIOS with one click.

ABIT-Engineered Flash Menu is a Windows-based BIOS flashing application.
FlashMenu™ will update your BIOS with one click.

1. HPT 370 BIOS and Driver 1.11 0512.

1. HPT 370 Driver v1.0.3b.
   
2. HPT 370 BIOS v1.0.3b1.
   
3. Load Utility v1.14.

1. Added hot key wording to enter BIOS setup when full screen logo enabled.
2. Changed the option wording from "OnChip SATA" to "OnChip SATA RAID" for "Bootable Add-in Device".
3. Changed the default setting of "OnBoard IR Port" to "Disabled".
4. Fixed the booting failure problem of Maxtor SATA HDD (Model name: 6Y120M0) in ICH5R RAID 0 status.
5. Changed the option wordings of "Boot Device" from "ZIP100" to "ZIP100/250" and from "USB-ZIP" to "USB-ZIP/LS120".
6. Enhanced the system stability when over clocks the CPU FSB over 255 MHz with CPU:DRAM = 1:1 setting.
7. Revised the wording of memory status from "DDR at Bank" to "DDR at DIMM" in system configuration table.
8. Included new Intel CSA LAN boot agent v1.21.07 for 82547EI chip (for IC7-G only).
9. Displayed correct specification of DDR200 memory module during POST.
10. Fixed the problem that specific CD-ROM device could not be correctly detected when there is specific HDD connected onto the same IDE cable.
11. Updated CPU micro code (0F24H/1EH, 0F25H/15H, 0F27H/37H, 0F29H/17H).
12. Revised display wording of "Time Alarm" menu box in BIOS setup.
13. BIOS Compile Date: 8/21/2003.
    
    
    

1. Updated CPU micro code (0F12H/2EH, 0F13H/05H)
2. Fixed the problem that no effect during POST if change "Delay IDE Initial" in BIOS setup.
3. Added function to automatically detect the IRQ availability and dynamically update assignation table in PnP/PCI configurations setup page.
4. Revised the wording of IEEE1394 controller in PCI device listing.
5. Fixed the problem that DOS4GW.EXE causes system hang-up in DOS environment.
6. Added function that automatically detects CPU operation speed after discharging CMOS data.
7. Added SATA RAID 1 function for Intel ICH5R south bridge.The IAA RAID driver should be updated to v3.5 or later to support RAID 1 in Windows XP.
   http://downloadfinder.intel.com/scripts-df/download.asp?url=/6363/eng/iaar35_enu.exe&ProductID=961
8. BIOS Compile date: 7/11/2003.

BIOS ID:15

1. Shows the correct IRQ of IDE Controller in PCI Devices Listing.
2. Fixes CPU Thermal Throttling behavior while under minus temperature, and supports minus temperature reading in BIOS Setup.
3. Fixes the problem that system could not automatically get into S4 mode, after enabling Power Scheme of "power Option" under Windows XP.
4. Fixes wrong system operation caused by incomplete discharging CMOS data by CCMOS jumper.
5. BIOS Compile Date: 6/23/2003.

New Fixes/Features

1. Added new option "HDD Change Message" in Advanced BIOS Features and the default setting is "Disabled". If this option is changed to "Enabled", the system will show warning message and prompt for a confirmation when one or more than one HDD had been added into or removed from the system.
2. Changed the default setting of "OnCip Serial ATA" to "Auto".
3. Revised the wording of IDE channels inside the BIOS Setup. IDE Channel 0, 1, 2, and 3 are changed to 1, 2, 3, and 4.
4. Revised the error reading of fan speed for specific CPU cooling fan when FanEQ 60% enabled.
5. Fixed "CPU THRM-Throttling" function.
6. Fixed the slow detection problem when HDD simulation card installed.
7. Fixed the problem that SMARTDRV.EXE malfunction in DOS 6.22 environment.
8. Fixed the problem that Windows 98 bootable floppy disk causes system hang up during loading CD-ROM driver when "OnChip Serial ATA" is set to "Auto".
9. Added "Game Accelerator" technology.
10. Removed options "Virus Warning" and "Force Update ESCD".
11. BIOS Compile Date: 6/9/2003.

1. Fixed DOS 6.22 booting failure from FAT16 partition.
2. Revised display mode of HTT CPU LOGO.
3. Fixed BIOS hang-up problem which is caused by specific CPU cooling fan reporting error RPM to BIOS when CPU FanEQ 60% enabled.
4. Revised the following default settings in BIOS setup page.
   - Bootable Add-in Device: PCI Slot Device
   - CPU FanEQ Active Temperature: 70 C
   - CPU Warning Temperature: 85 C
5. Enabled "IDE Block Mode" and hid the option.
6. Revised ICH5R RAID BIOS display issue.
7. Fixed COM2 device existing in Windows Device Manager problem.
8. Revised power-on delay time from 4~5 seconds to 1~2 seconds after AC powerloss and resume.
9. BIOS Compile Date: 5/19/2003.

BIOS ID: 11

1. Added new option "SATA RAID ROM" to setup the BIOS of onboard and on-chip SATA.
2. Revised setup menu for on-chip Serial ATA.
3. Fixed IOMEGA USB-ZIP 250 boot issue.
4. Added SVID/SDID for IC7 and IC7-G respectively.
5. Added "Intel on-screen branding" and could be enabled/disabled.
6. Added new options "Read Delay (Trd)" and "Turbo Mode" for system performance.
7. Fixed on-chip SATA boot issue while another bootable hard drives exist and attached to IDE-1 or IDE-2.
8. Updated memory reference code and ICH5 BIOS spec to v1.2.
9. Updated ICH5 SATA RAID BIOS to v3.0.0.2344.
10. Updated CPU micro code (CPU: 0F29H, ID=11H).
11. Added new options "Refresh Cycle Time", "Read Delay Adjust (tRD Adj)", "Command Per Clock (CPC)", and "Performance Mode".
12. Added new option "IDE Bus Master".
13. Added CPU multiplier 8X for engineering sample CPU and maximum CPU frequency 412 MHz.
14. Fixed DRAM timing settings while manually set them.
15. BIOS Compile Date: 4/30/2003.

1. First release.
2. BIOS Compile Date: 3/27/2003.

1. The Driver is for Windows* 2000, Windows* 98 SE, Windows* Me, Windows* XP Home Edition, Windows* XP Professional.
2. Intel INF Update v5.00.1015.

1. Multi-Language.
2. Intel® Application Accelerator RAID Edition for WindowsXP.
3. There is no necessary to install the program until you enable the "RAID Function" in the BIOS menu of "OnChip Serial ATA".
4. The floppy disk containing RAID driver files which can be used to pre-install RAID driver during the F6 portion of WindowsXP setup.

1. Floppy.
2. Intel® Application Accelerator RAID Edition for WindowsXP.
3. There is no necessary to install the program until you enable the "RAID Function" in the BIOS menu of "OnChip Serial ATA".
4. The floppy disk containing RAID driver files which can be used to pre-install RAID driver during the F6 portion of WindowsXP setup.

1. The Driver is for WinNT.
2. Audio Driver 3.44

1. The Driver is for Win98SE/Me/2000/XP.
2. Audio Driver 3.44

1. The Driver is for Win95/98.
2. Audio Driver 3.44

1. The Driver is for Win98SE/Me.
2. For Windows 2000 users, please upgrade to Service Pack 4 or later.
3. For Windows XP users, please upgrade to Service Pack 1 or later.

1. Hardware Monitor

1. Added hot key wording to enter BIOS setup when full screen logo enabled.
2. Changed the option wording from "OnChip SATA" to "OnChip SATA RAID" for "Bootable Add-in Device".
3. Changed the default setting of "OnBoard IR Port" to "Disabled".
4. Fixed the booting failure problem of Maxtor SATA HDD (Model name: 6Y120M0) in ICH5R RAID 0 status.
5. Changed the option wordings of "Boot Device" from "ZIP100" to "ZIP100/250" and from "USB-ZIP" to "USB-ZIP/LS120".
6. Enhanced the system stability when over clocks the CPU FSB over 255 MHz with CPU:DRAM = 1:1 setting.
7. Revised the wording of memory status from "DDR at Bank" to "DDR at DIMM" in system configuration table.
8. Included new Intel CSA LAN boot agent v1.21.07 for 82547EI chip (for IC7-G only).
9. Displayed correct specification of DDR200 memory module during POST.
10. Fixed the problem that specific CD-ROM device could not be correctly detected when there is specific HDD connected onto the same IDE cable.
11. Updated CPU micro code (0F24H/1EH, 0F25H/15H, 0F27H/37H, 0F29H/17H).
12. Revised display wording of "Time Alarm" menu box in BIOS setup.
13. BIOS Compile Date: 8/21/2003.
    
    
    

1. Updated CPU micro code (0F12H/2EH, 0F13H/05H)
2. Fixed the problem that no effect during POST if change "Delay IDE Initial" in BIOS setup.
3. Added function to automatically detect the IRQ availability and dynamically update assignation table in PnP/PCI configurations setup page.
4. Revised the wording of IEEE1394 controller in PCI device listing.
5. Fixed the problem that DOS4GW.EXE causes system hang-up in DOS environment.
6. Added function that automatically detects CPU operation speed after discharging CMOS data.
7. Added SATA RAID 1 function for Intel ICH5R south bridge.The IAA RAID driver should be updated to v3.5 or later to support RAID 1 in Windows XP.
   http://downloadfinder.intel.com/scripts-df/download.asp?url=/6363/eng/iaar35_enu.exe&ProductID=961
8. BIOS Compile date: 7/11/2003.

BIOS ID:15

1. Shows the correct IRQ of IDE Controller in PCI Devices Listing.
2. Fixes CPU Thermal Throttling behavior while under minus temperature, and supports minus temperature reading in BIOS Setup.
3. Fixes the problem that system could not automatically get into S4 mode, after enabling Power Scheme of "power Option" under Windows XP.
4. Fixes wrong system operation caused by incomplete discharging CMOS data by CCMOS jumper.
5. BIOS Compile Date: 6/23/2003.

New Fixes/Features

1. Added new option "HDD Change Message" in Advanced BIOS Features and the default setting is "Disabled". If this option is changed to "Enabled", the system will show warning message and prompt for a confirmation when one or more than one HDD had been added into or removed from the system.
2. Changed the default setting of "OnCip Serial ATA" to "Auto".
3. Revised the wording of IDE channels inside the BIOS Setup. IDE Channel 0, 1, 2, and 3 are changed to 1, 2, 3, and 4.
4. Revised the error reading of fan speed for specific CPU cooling fan when FanEQ 60% enabled.
5. Fixed "CPU THRM-Throttling" function.
6. Fixed the slow detection problem when HDD simulation card installed.
7. Fixed the problem that SMARTDRV.EXE malfunction in DOS 6.22 environment.
8. Fixed the problem that Windows 98 bootable floppy disk causes system hang up during loading CD-ROM driver when "OnChip Serial ATA" is set to "Auto".
9. Added "Game Accelerator" technology.
10. Removed options "Virus Warning" and "Force Update ESCD".
11. BIOS Compile Date: 6/9/2003.

1. Fixed DOS 6.22 booting failure from FAT16 partition.
2. Revised display mode of HTT CPU LOGO.
3. Fixed BIOS hang-up problem which is caused by specific CPU cooling fan reporting error RPM to BIOS when CPU FanEQ 60% enabled.
4. Revised the following default settings in BIOS setup page.
   - Bootable Add-in Device: PCI Slot Device
   - CPU FanEQ Active Temperature: 70 C
   - CPU Warning Temperature: 85 C
5. Enabled "IDE Block Mode" and hid the option.
6. Revised ICH5R RAID BIOS display issue.
7. Fixed COM2 device existing in Windows Device Manager problem.
8. Revised power-on delay time from 4~5 seconds to 1~2 seconds after AC powerloss and resume.
9. BIOS Compile Date: 5/19/2003.

BIOS ID: 11

1. Added new option "SATA RAID ROM" to setup the BIOS of onboard and on-chip SATA.
2. Revised setup menu for on-chip Serial ATA.
3. Fixed IOMEGA USB-ZIP 250 boot issue.
4. Added SVID/SDID for IC7 and IC7-G respectively.
5. Added "Intel on-screen branding" and could be enabled/disabled.
6. Added new options "Read Delay (Trd)" and "Turbo Mode" for system performance.
7. Fixed on-chip SATA boot issue while another bootable hard drives exist and attached to IDE-1 or IDE-2.
8. Updated memory reference code and ICH5 BIOS spec to v1.2.
9. Updated ICH5 SATA RAID BIOS to v3.0.0.2344.
10. Updated CPU micro code (CPU: 0F29H, ID=11H).
11. Added new options "Refresh Cycle Time", "Read Delay Adjust (tRD Adj)", "Command Per Clock (CPC)", and "Performance Mode".
12. Added new option "IDE Bus Master".
13. Added CPU multiplier 8X for engineering sample CPU and maximum CPU frequency 412 MHz.
14. Fixed DRAM timing settings while manually set them.
15. BIOS Compile Date: 4/30/2003.