|
|
| BIOS 更新注意事項:
- 如果您需要更進一步的資訊來得知您的主機板型號版本、或是如何更新BIOS,請連結
這裡.
- 請注意,要更新 BIOS,除了需下載 BIOS 檔案外,您還需要 Flash
Utility 。在較新版本 (2001 年 8 月之後) 的 BIOS 檔案中則已包含了更新程式,但較舊版本仍需另外下載。
- 其它 BIOS 相關問題,請按這裡
- 如果您不需要新版 BIOS 所需的改進或修正,您並不需要更新 BIOS。
- 您不需要每一版 BIOS 漸次更新,只要直接更新至最新版本即可包含之前的所有修正跟改進。
- 在更新 BIOS 之後,CMOS 資料將會消失。在重新開機後,您必需進入 BIOS 重新設定您的系統資訊。
| 主機版>Socket 478>IS7-E
| Bios Issue Date:2004/11/23 | BIOS ID:2.3 | |
- 更新 CPU micro code.
- 對於部分市售 INTEL CPU 增加可調最大及最小倍頻的功能.
- 支援 "OnChip Serial ATA" 在 "Enhanced Mode" 時使用SATA CDROM.
- 變更 "PWM Shutdown Temperature" 預設為"Disabled", "CPU Warning Temperature" 預設溫度至95度C.
- BIOS 日期: 11/23/2004
|
| Bios Issue Date:2004/08/16 | BIOS ID:2.2 | |
- 更新CPU micro code.
- BIOS日期: 08/16/2004
|
| Bios Issue Date:2004/04/27 | BIOS ID:2.0 | |
- 更新 CPU Micro Code.
- 當 "Onboard Network Controller" 關閉時,MAC Address 仍會出現在 System Configuration
中。
- 新增 AWDFLASH v8.32 支援 "ALT+F2" 熱鍵功能。
- 增加對部分電源供應器的相容性。
- 修正無法關閉 "OnChip SATA Raid Rom" 的問題。
- 校正 CPU 溫度。
- 新增 "PWM Shutdown Temperature" 選項。
- 新增 "PWM Warning Temperature" 選項。
- BIOS 日期: 04/27/2004
|
| Bios Issue Date:2004/03/12 | BIOS ID:1.9 | |
- 修正當使用P4 Prescott 2.4G (533MHz/ 1M L2/ 90nm) CPU 會出現"CPU is unworkabled"
的錯誤訊息。請依照下例步驟更新BIOS。
- 當螢幕出現 "CPU is unworkabled" 訊息時按下 <F1> 繼續進行開機程序。
- 自磁片開機並且進行更新BIOS動作。
- BIOS 日期 : 03/12/2004。
|
| Bios Issue Date:2004/02/23 | BIOS ID:1.8 | |
- 修正當 SATA 及 PATA 硬碟同時存在時,並將作業系統安裝在SATA硬碟上,之後再將 PATA 硬碟移除後無法開機之問題。
- 新增 Prescott CPU 的micro code。
- 更改預設年份為2004。
- 更新 Intel OSB logo。
- 增加對部分非-RAID卡的相容性。
- 更新INTEL RAID BIOS版本為3.5.0.3003。
- BIOS 日期: 02/23/2004。
|
| Bios Issue Date:2003/11/04 | BIOS ID:1.7 | |
- Updated CPU micro code.
- Added Pentium 4 Extreme Edition support.
- Fixed the problem where the CAS latency can not be set manually when the
CPU:DRAM is set to PSB8000/5:4 or PSB800/3:2.
- Fixed the problem where the hard disk will not be recognized if the OnChip
SATA is set to "Combined Mode" then choose "RAID".
- Fixed the problem where system will reboot when the "Resume by Alarm" is
enabled and user pressed power button to shutdown the system during POST.
- Fixed HDD size detected as 136GB when 200/250/300 GB SATA drives are connected
to SATA1 or SATA2 (ICH5 SATA channels).
- BIOS compile date: 11/04/2003
|
| Bios Issue Date:2003/08/15 |
- 更新 CPU micro code 0F29H/14H)。
- 當採用全螢幕 LOGO 時在其下方顯示文字提示- Del to enter BIOS setup。
- 變更 "Bootable Add-in Device" 選項文字,從 "OnChip SATA" 改為
"OnChip SATA RAID"。
- 將 "OnBoard IR Port" 的預設值修改成 "Disabled"。
- 修正 Maxtor SATA 硬碟(型號 6Y120M0)在 IS7G_15 版本 BIOS 無法在 ICH5R 南橋組成 RAID 0 的問題。(僅
IS7-G 和 IS7 受影響)
- 變更 "Boot Device" 選項文字,將 "ZIP100" 改為 "ZIP100/250";同時也將
"USB-ZIP" 改為 "USB-ZIP/LS120"。
- 改善當 CPU:DRAM = 1:1 而且 CPU 頻率超頻至 255 MHz 以上系統不穩的問題(請注意超頻使用並非產品保固範圍內)
- 更改開機時 System Configurations Table 當中記憶體狀態顯示方式,從 "DDR at Bank"
變更為 "DDR at DIMM"。
- 修正某些特定光碟機和某些特定硬碟機串接在同一條 IDE 排線上會有偵測不到的問題。
- BIOS 日期: 8/15/2003。
|
| Bios Issue Date:2003/07/02 | BIOS ID:14 | |
- 修正 CMOS 因為無法以硬體方式抹除乾淨,而造成程式讀取時的錯誤,導致系統因為誤判而造成誤動作的情形。
- 修正 PCI Devices Listing 中關於 IDE Controller 所佔用的 IRQ,使其顯示正確之 IRQ 編號。
- 修正當負溫度時,其 CPU Thermal Throttling 動作不正常的情形,並支援 BIOS Setup 中負溫度之顯示。
- 修正 Win XP 中使用 "Power Option" 中之 Power Scheme,其無法自行進入 S4
狀態的情形。
- Update CPU Microcode (CPUID=0F13h, Patch ID=05h ; CPUID=0F12h, Patch
ID=02eh)。
- 修正"- Bootabled Add-in Device" Function 無法由 PCI Slot Device
優先啟動之問題。
- BIOS 日期: 7/02/2003。
|
| Bios Issue Date:2003/06/10 | BIOS ID:13
New Fixes/Features
- Added support for IS7-G, IS7, and IS7-E.
- Updated CPU micro code (CPU: 0F29H, ID=11H).
- Added CPU multiplier 8X for engineering sample CPU and maximum CPU frequency
412 MHz.
- Revised setup menu for OnChip Serial ATA.
- Fixed on-chip SATA boot issue while another bootable hard drives exist and
attached to IDE-1 or IDE-2.
- Updated memory reference code and ICH5 BIOS spec to v1.2.
- Fixed PS/2 mouse malfunctioning problem while the USB cable of Media XP
attached to mainboard.
- Fixed DOS 6.22 booting failure from FAT16 partition.
- Fixed BIOS hang-up problem which is caused by specific CPU cooling fan reporting
error RPM to BIOS when CPU FanEQ 60% enabled.
- Revised the following default settings in BIOS setup page. - Bootable Add-in
Device: PCI Slot Device - CPU FanEQ Active Temperature: 70 C - CPU Warning
Temperature: 85 C
- Added 80, 85, and 90 degrees C into "Shutdown Temperature".
- Enabled "IDE Block Mode" and hided the option.
- Revised ICH5R RAID BIOS display issue.
- Revised power-on delay time from 4~5 seconds to 1~2 seconds after AC power
lost and resumed.
- Added description for "Bootable Add-in Device".
- Fixed the problem that NB fan still reports full speed in PC Health page
when "CPU FanEQ Speed Control" is enabled.
- Added new option "IDE Bus Master".
- Added description for "Shutdown when CPUFAN Fail".
- Revised the wording of IDE channels inside the BIOS Setup. IDE Channel 0,
1, 2, and 3 are changed to 1, 2, 3, and 4.
- Added new option "SATA RAID ROM" to setup both "OnBoard SATA"
and "OnChip SATA".
- Added new option "HDD Change Message" in Advanced BIOS Features
and the default setting is "Disabled". If this option is changed
to "Enabled",the system will show warning message and prompt for
a confirmation whenone or more than one HDD had been added into or removed
from the system.
- Fixed "CPU THRM-Throttling" function.
- Added new options "Refresh Cycle Time", "Read Delay Adjust
(tRD Adj)", and "Command Per Clock (CPC)".
- Changed the default setting of "Drive A" from "None"
to "1.44M" after Load Fail-safe Defaults.
- Changed the default setting of "OnCip Serial ATA" to "Auto".
- Added "Game Accelerator" technology.
- Revised the error reading of fan speed for specific CPU cooling fan when
FanEQ 60% enabled.
- Fixed the slow detection problem when HDD simulation card installed.
- Fixed the problem that SMARTDRV.EXE malfunction in DOS 6.22 environment.
- Fixed the problem that Windows 98 bootable floppy disk causes system hang
up during loading CD-ROM driver when "OnChip Serial ATA" is set
to"Auto" or "Enhanced Mode".
- Removed the option "Force Update ESCD".
- BIOS Compile Date: 6/10/2003.
|
| Bios Issue Date:2003/04/23 | BIOS ID:11
- 首次發行
- BIOS 日期: 4/11/2003.
|
|
|
| |